I've ordered one I'm planning on making it for my girlfriend for a stocking filler at Xmas. after reading these comments though it seems harder to do than they make out. and Im doing it as a surprise so I won't have my girl there to lick balls and shove her pussy in my face to keep me hard. so my plan of action will be to practice a few times without the mould to make sure I can maintain a full erection. secondly I will be using a very tight cock ring, I will take a viagra half hour before hand and I will have some porn on to watch to hopefully keep me excited. I'll post results when I've done it.wish me luck guys.
Clone A Willy Tips?
- Thread starter Nikolas1
- Start date
nickinoo
Legendary Member
- Joined
- Aug 28, 2012
- Posts
- 809
- Media
- 4
- Likes
- 1,472
- Points
- 248
- Location
- Birmingham (England)
- Sexuality
- 99% Gay, 1% Straight
- Gender
- Male
Yeah. I made one for a hotwife couple as a teaser before we met. She said the rubber material was very grippy and even with a lot of lube it was hard to use. I have thought about making my own kit using life casting supplies and some silicone rubber.
I made a clone some days ago. and its not the best but I really liked it. You never know how your dick really looks until you clone it
I tried the Clone your willy kit two times, without getting a nice result.
Some time ago I found a company which sells everything you need to make a clone.....
It's not really easy,but it works !!
http://www.siliconesandmore.com/en/
Have fun and succes !!!
Some time ago I found a company which sells everything you need to make a clone.....
It's not really easy,but it works !!
http://www.siliconesandmore.com/en/
Have fun and succes !!!
Very true. I know this threads getting a bit thin, but couldn't resist.
I cloned mine a few months ago. I tried following the instructions, but that was an epic fail. I ended up making a special pump chamber that opened at the top. Stayed pumped while doing the prep work. Poured in the alginate, closed it and pumped back up to maximum erection. Then waited 10 minutes, twice what the instructions. When I released the vacuum on the pump I couldn't feel any release, that's how I knew it was fully set. I released the seal from the bottom and almost instantly deflated out of it. Worked like a charm (finally after a half dozen failures). Then I added another step. I made a plaster positive with Durham's Rock Hard. Seemed appropriate. ;D Cleaned up any holes on the plaster model and made a second two part mold with tin cure silicone. I bought 2 kits just for the platinum cure silicone. Adjusted the colour since I'm considerably darker than the kit. I didn't get a perfect match colorwise, but it's much more realistic at least. I also added a much better vibrator.
Attachments
Does it look bigger or smaller then u now that it isnt attached to u.
XXXWolverineXXX
Superior Member
I have made lots of them and me and my girl give them a gifts to her girlfriends. This is one I made with a vibrating bullet inside and I put a bicycle hand grip on it too. We also have clone parties were we have the couple make one then they have to pick there mates clone out. It's super fun plus lots of drank and fucking. ![IMG_3715.JPG]( "IMG_3715.JPG")
twoton
Superior Member
- Joined
- Feb 28, 2011
- Posts
- 7,862
- Media
- 1
- Likes
- 8,353
- Points
- 268
- Location
- Mid Atlantic
- Sexuality
- 99% Straight, 1% Gay
- Gender
- Male
That's a lot of work, but the results look worth it. It looks like you have a pronounced curve--was the tube wide enough to accommodate it?
The idea is fun but the making of it was challenging. I found the tube that comes with the kit was not wide enough for my size and angle, ended up buying 2 packets of the mixture and using a large water bottle to make the clone. If you are larger, a single silicone that comes with the kit probably won't be enough to make a clone of your whole shaft.
We used a Create-a-Mate kit years ago. It was hilariously fun trying to get the water temp right for the alginate, mix it up, get it to pour into the mold, stay hard whilst this mayhem is occurring.... It failed on both of our attempts but was fun. I blame the tube which was way too wide for a human penis...8" diameter?????....but had a 2" hole to pour the thick alginate mix into.
The kit also clearly didn't have enough rubber mix to make a dildo. Emails to the mfg. asking for more got no response, so screw 'em. I bought alginate from a craft store and used a simple open container. Mixed it right in that container, wore a cock ring, and plunged myself in. Perfect mold. I used Durham's water putty for the positive, painted it, and if we ever decide to try making a rubber toy, can use this as the positive.
The kit also clearly didn't have enough rubber mix to make a dildo. Emails to the mfg. asking for more got no response, so screw 'em. I bought alginate from a craft store and used a simple open container. Mixed it right in that container, wore a cock ring, and plunged myself in. Perfect mold. I used Durham's water putty for the positive, painted it, and if we ever decide to try making a rubber toy, can use this as the positive.
- Joined
- Apr 8, 2016
- Posts
- 1,218
- Media
- 289
- Likes
- 7,848
- Points
- 433
- Location
- Connecticut (United States)
- Verification
- View
- Sexuality
- 50% Straight, 50% Gay
- Gender
- Male
That's only a spare 1" per side. Not ridiculous as they no doubt want to sell extra product.
Sorry about the prolonged delay. Haven't been online much since then. But to answer your question: the tube was a length of 3 inch pvc pipe with a quick connect fitting set in a slip cap. If I could have gotten acrylic tubing, I would have used that instead. But there's nothing like that around here and I didn't want to order it. I smoothed the ends first with a sander and then with heat. Where the cap went on, I sanded the outside of the pipe a wee bit and smeared it with silicone lubricant used in pool and spa pumps to get the cap off easily.
